Thorp Air Command - T18.net

Supporting Owners, Builders and Pilots of the Thorp T-18 and its variants.
It is currently Thu Mar 28, 2024 3:21 pm

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 25 posts ]  Go to page 1, 2  Next
Author Message
Pacer 20
 Post subject: Aileron weight.
PostPosted: Sun May 26, 2013 12:58 pm 
Sr. Member
Sr. Member

Joined: Sat Feb 09, 2013 11:34 am
Posts: 233
Location: Montreal, Canada
Hi!

Quick info what do you think about the third hole on the bending square tube.
Is it possible that the third hole is a starting point for a possible rupture?
I'm not a Thorp specialist but I never want to loose this weight on flight.

Image

Image

I need to sand blast the arm and see if some small crack is begening.
I want to know your idea about that!
Thanks again.

_________________
Thierry
French Canadian T-18
C-FPVE #091


Top
 Profile  
 
Rich Brazell
 Post subject: Re: Aileron weight.
PostPosted: Sun May 26, 2013 9:53 pm 
Hero Member
Hero Member

Joined: Wed Oct 21, 2009 12:33 pm
Posts: 3095
Images: 64
Location: Jamul, CA (San Diego area)
I would be very cautious ! I am not a welding guy , but it may be possible to close up the 3rd hole with a torch ? Or cut and splice a new piece in . Or make an entire new weight/arm . Or buy one ?

RB O0


Top
 Profile Personal album  
 
dan
 Post subject: Re: Aileron weight.
PostPosted: Mon May 27, 2013 9:48 am 
Sr. Member
Sr. Member

Joined: Wed Oct 21, 2009 9:30 am
Posts: 898
Images: 0
Location: USA
That's a mild steel Tube Thierry, The hole is not in a spot being of high stress. Clean it up,spotless, 45degree countersink the hole to get into some fresh material and Tig it closed, Make sure there are no cracks, make sure the tube doesn't get hot enough to loosen the lead weight at the end of the Tube........Dan


Top
 Profile  
 
dan
 Post subject: Re: Aileron weight.
PostPosted: Mon May 27, 2013 9:59 am 
Sr. Member
Sr. Member

Joined: Wed Oct 21, 2009 9:30 am
Posts: 898
Images: 0
Location: USA
You can also put a piece of solid rod in the hole that runs from one side to the other and use it for filler,It would make the hole easier to fill and allow for less heat to close it up,weld bothe ends of the rod this will also reinforce the area with the hole in it if you are worried about the integrity of the tube. Dan


Top
 Profile  
 
Pacer 20
 Post subject: Re: Aileron weight.
PostPosted: Mon May 27, 2013 5:02 pm 
Sr. Member
Sr. Member

Joined: Sat Feb 09, 2013 11:34 am
Posts: 233
Location: Montreal, Canada
I open my AC43-13 and I see some interesting document. Dan your apsolutly true. I think a small welding with a inside doubler was correct.
I send you pictures after the reapir!!!

Merci.

_________________
Thierry
French Canadian T-18
C-FPVE #091


Top
 Profile  
 
ljkrume
 Post subject: Re: Aileron weight.
PostPosted: Thu Apr 03, 2014 1:38 pm 
Sr. Member
Sr. Member

Joined: Mon Oct 26, 2009 1:33 pm
Posts: 232
Images: 213
Location: USA
Hey guys,

Tried about 5 attempts to pour lead into a plaster mold with steel arms in it. Made nice patterns, nice mold, etc., but casting lead just doesnt work for me. I think plaster has too much air or something and I get a lot of bubbling. Let plaster sit for a week and in the oven 250F over an hour to get rid of any water vapor and still pretty poor castings. I've seen some that others have made and they look pretty rough too. I was hoping to come out good. Searching old newsletters I find nothing about making these.

Anyone with ideas on this, or a source of good ones to put on a new bird, please let me know. By the way, I recommend anyone to look back at the old newsletters. It's been a while for me and they're really fun.

Thanks, Les Krumel
Albuquerque


Top
 Profile Personal album  
 
Bill Williams
 Post subject: Re: Aileron weight.
PostPosted: Thu Apr 03, 2014 1:52 pm 
I made a mold out of thin steel and shaped it like a cookie cutter. Foiled taped a flat piece steel to close up one side and poured. I also tinned the square tube where it attaches to the lead.


Top
  
 
jrevens
 Post subject: Re: Aileron weight.
PostPosted: Thu Apr 03, 2014 3:00 pm 
Sr. Member
Sr. Member
User avatar

Joined: Thu Oct 22, 2009 10:13 pm
Posts: 789
Location: USA
Les,
In my experience, the trick to getting a good lead molded piece is to pre-heat the mold. You can't do that with plaster -because it hasn't got enough mass & other reasons. Steel or even aluminum works well with lead. If the mold is cold, the lead starts to harden as soon as it hits, causing stratification, possible voids, etc. If the mold is not too thin & has some mass, that helps too because it doesn't cool off as quick. I'll heat the mold to 400 or 500 degrees in the oven before taking it out & pouring the lead. I've even heated molds on the range top in the kitchen, while melting the lead right there also. My wife loves that.
It is important to tin the steel arms before molding the lead, as Bill said. Don't splash, but don't "piddle" around - pour it right in so that you're never pouring lead on top of lead that has already started to solidify.

_________________
John Evens
Arvada, Colorado

T-18 N71JE (sold)
Kitfox 7 SS N27JE


Top
 Profile  
 
James Grahn
 Post subject: Re: Aileron weight.
PostPosted: Fri Apr 04, 2014 9:47 am 
Hero Member
Hero Member

Joined: Sat Oct 24, 2009 7:16 pm
Posts: 1434
Images: 0
Location: USA
Or you can call Mike.
I'll have the weight molds shortly (as soon as Mike gets healthy) and I'll pour you some.
Cubes


Top
 Profile Personal album  
 
ljkrume
 Post subject: Re: Aileron weight.
PostPosted: Wed Sep 17, 2014 11:58 pm 
Sr. Member
Sr. Member

Joined: Mon Oct 26, 2009 1:33 pm
Posts: 232
Images: 213
Location: USA
Hey guys,

I'm still in need of aileron weights. If none are available I'll try milling a mold from aluminum. I'm down to a short one-page checklist of things to do before N48LK is ready for airworthiness inspection. Getting exciting now.

Thanks.
Les Krumel,
Albuquerque


Top
 Profile Personal album  
 
fytrplt
 Post subject: Re: Aileron weight.
PostPosted: Thu Sep 18, 2014 6:19 am 
Hero Member
Hero Member
User avatar

Joined: Tue Oct 20, 2009 8:07 pm
Posts: 1140
Images: 2
Location: Lakeland, Florida, USA
Les,

I made my molds out of some scrap strip steel. I cut a notch in the cookie cutter looking mold to let the arm with pin in. The whole thing was placed on a plate for the pour. Easy to knock it out once cooled. Don't make the project harder than it is.

_________________
Bob Highley
N711SH
SN 835
KLAL


Top
 Profile Personal album  
 
leewwalton
 Post subject: Re: Aileron weight.
PostPosted: Thu Sep 18, 2014 8:29 am 
Administrator
Administrator
User avatar

Joined: Tue Oct 20, 2009 4:09 pm
Posts: 1705
Images: 107
Location: Houston, TX
Les, I have a few sets of spares. You're welcome to a set.

_________________
Lee Walton
Houston, TX
N51863,N118LW
KEFD


Top
 Profile Personal album  
 
James Grahn
 Post subject: Re: Aileron weight.
PostPosted: Fri Sep 19, 2014 10:21 pm 
Hero Member
Hero Member

Joined: Sat Oct 24, 2009 7:16 pm
Posts: 1434
Images: 0
Location: USA
I can make some too. Let me know.
Cubes


Top
 Profile Personal album  
 
ljkrume
 Post subject: Re: Aileron weight.
PostPosted: Mon Sep 22, 2014 7:59 pm 
Sr. Member
Sr. Member

Joined: Mon Oct 26, 2009 1:33 pm
Posts: 232
Images: 213
Location: USA
Thanks for the response guys.

Bob, I tried 5 times with the mold I made and a couple of times the problem I had was springing a leak. Just a small crack and what a mess! I think I did good with the rest of the project and wanted to a nice job with this too. I might be able to get it but I'm real close to the finish line; the best thing at this point is just to get a pair already made.

Lee, if you already have a good set please PM me and let me know what I need to do.

Thanks again,
Les K


Top
 Profile Personal album  
 
bloke727
 Post subject: Re: Aileron weight.
PostPosted: Mon Dec 10, 2018 1:10 pm 
Newbie
Newbie

Joined: Tue Jul 23, 2013 5:49 pm
Posts: 4
What is the approved aileron balance? I see some people are adding aileron trim which will move the CG aft. How much does this affect balance and how critical is the aileron weight (for example, how much weight can the aileron trailing edge have)?


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 25 posts ]  Go to page 1, 2  Next

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 9 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron

[ Time : 0.300s | 13 Queries | GZIP : On ]