I'd sell my O-320 T18 for close to that. No assembly required, flying and recent condition inspection.
| Thorp Air Command - T18.net http://thorp18.com/thorpforum/ |
|
| T18 forsale in Granbury, Texas http://thorp18.com/thorpforum/viewtopic.php?f=46&t=8408 |
Page 1 of 1 |
| Author: | Ryan Allen [ Sat Oct 12, 2019 3:52 pm ] |
| Post subject: | T18 forsale in Granbury, Texas |
Saw this in the Dallas Craigslist ads and thought I would share it: https://dallas.craigslist.org/ftw/avo/d ... 25804.html |
|
| Author: | James Grahn [ Sat Oct 12, 2019 11:41 pm ] |
| Post subject: | Re: T18 forsale in Granbury, Texas |
I’d have to have that baggage cut analyzed. First glance, it looks too big. Not fond of the RV add on stuff. I’m dealing with one of those myself. Needs ADSB. But a good start. Any engineers out there know if 3/32 half spacing rivets are as good or stronger than 1/8”? Cubes |
|
| Author: | Andy475 [ Sun Oct 13, 2019 9:57 am ] |
| Post subject: | Re: T18 forsale in Granbury, Texas |
Cubes, Are there drawings/guidance or any engineering data on the baggage compartment cuts? -Andy |
|
| Author: | fytrplt [ Sun Oct 13, 2019 3:52 pm ] |
| Post subject: | Re: T18 forsale in Granbury, Texas |
I have the Sunderland deck mod drawings. PM me. |
|
| Author: | James Grahn [ Sun Oct 13, 2019 5:13 pm ] |
| Post subject: | Re: T18 forsale in Granbury, Texas |
Look at the 669 drawing. It shows the cutout. From my plans, the sides are a minimum of 2.4” and the front is 3.2”. It has a rolled edge of .375. Cubes |
|
| Author: | James Grahn [ Sun Oct 13, 2019 5:16 pm ] |
| Post subject: | Re: T18 forsale in Granbury, Texas |
Sounds like you can swap 1/8” rivets for 3/32” if you have enough. Cubes |
|
| Author: | leewwalton [ Sun Oct 13, 2019 5:53 pm ] |
| Post subject: | Re: T18 forsale in Granbury, Texas |
That project has gone up for sale several times ... same situation... he just wants too much for a project that being said those who know the workmanship have vouched for its excellence. |
|
| Author: | Unclerap [ Sun Oct 13, 2019 6:37 pm ] |
| Post subject: | Re: T18 forsale in Granbury, Texas |
I'd sell my O-320 T18 for close to that. No assembly required, flying and recent condition inspection.
|
|
| Author: | James Grahn [ Sun Oct 13, 2019 8:29 pm ] |
| Post subject: | Re: T18 forsale in Granbury, Texas |
Post that in the classified section. I’ve had several calls looking for flying Thorps recently. Cubes |
|
| Author: | Unclerap [ Mon Oct 14, 2019 6:51 pm ] |
| Post subject: | Re: T18 forsale in Granbury, Texas |
James Grahn wrote: Post that in the classified section. I’ve had several calls looking for flying Thorps recently. Cubes Done, I bumped my previous classified. Thanks, Rap |
|
| Author: | Gary Green [ Tue Oct 15, 2019 2:24 pm ] |
| Post subject: | Re: T18 forsale in Granbury, Texas |
This T-18 previously had an airworthiness certificate and was registered. The ad doesn't mention the damage incurred that resulted in the rebuild and modifications over the decades. But the workmanship is quite good. |
|
| Page 1 of 1 | All times are UTC - 6 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|