Thorp Air Command - T18.net

Supporting Owners, Builders and Pilots of the Thorp T-18 and its variants.
It is currently Wed Nov 30, 2022 6:00 am

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 247 posts ]  Go to page Previous  1 ... 11, 12, 13, 14, 15, 16, 17  Next
Author Message
Ryan Allen
PostPosted: Sun Dec 13, 2020 10:48 am 
Hero Member
Hero Member
User avatar

Joined: Wed Oct 21, 2009 6:10 pm
Posts: 1066
Images: 0
Location: Louisiana
Yes, I was thinking the same thing Les because there is no seal where the shaft exits the top of the cylinder. Looking at the parts manual, it confirms there is no seal around there either. Based on your experience, I think I will drain a little fluid from the reservoir and see what happens. Thanks for all the input.


Top
 Profile Personal album  
 
Ryan Allen
PostPosted: Sun Dec 13, 2020 1:56 pm 
Hero Member
Hero Member
User avatar

Joined: Wed Oct 21, 2009 6:10 pm
Posts: 1066
Images: 0
Location: Louisiana
That was it Les, thanks for your input! I drained a teaspoon or so from each cylinder, and viola, no more leak. Thanks again.


Top
 Profile Personal album  
 
James Grahn
PostPosted: Sun Dec 13, 2020 4:47 pm 
Hero Member
Hero Member

Joined: Sat Oct 24, 2009 7:16 pm
Posts: 1351
Images: 0
Location: USA
All true. And the piston actually floats on the end of the shaft. What that means is that the piston needs pressure from the shaft to actually seal and provide brake pressure. Once you release the pedal, the pressure from the shaft on the piston is released and therefore, fluid can flow both directions. Just FYI.
Also, for those who need them, we have partnered with Matco Brakes. They are great people and provide us with an excellent discount.
Cubes


Top
 Profile Personal album  
 
Ryan Allen
PostPosted: Tue Dec 29, 2020 8:47 am 
Hero Member
Hero Member
User avatar

Joined: Wed Oct 21, 2009 6:10 pm
Posts: 1066
Images: 0
Location: Louisiana
Those of you that have air intake from your rear baffle, could you post some photos of your setup. I would really like to pursue this installation. I assume you need a horizontal induction sump.

Also, are there any drawings regarding the cowling installation? I didn't find any in my set.


Top
 Profile Personal album  
 
ljkrume
PostPosted: Tue Dec 29, 2020 10:26 am 
Sr. Member
Sr. Member

Joined: Mon Oct 26, 2009 1:33 pm
Posts: 229
Images: 213
Location: USA
Ryan, I did induction off the rear baffle with an updraft carb and large scat. Take a look in photo albums... Les


Top
 Profile Personal album  
 
fytrplt
PostPosted: Tue Dec 29, 2020 12:45 pm 
Hero Member
Hero Member
User avatar

Joined: Tue Oct 20, 2009 8:07 pm
Posts: 1110
Images: 2
Location: Lakeland, Florida, USA
Image
Looking in from the right side. Connects to the air filter with 3" scat.

_________________
Bob Highley
N711SH
SN 835
KLAL


Top
 Profile Personal album  
 
fytrplt
PostPosted: Tue Dec 29, 2020 12:47 pm 
Hero Member
Hero Member
User avatar

Joined: Tue Oct 20, 2009 8:07 pm
Posts: 1110
Images: 2
Location: Lakeland, Florida, USA
Image

_________________
Bob Highley
N711SH
SN 835
KLAL


Top
 Profile Personal album  
 
Ryan Allen
PostPosted: Tue Dec 29, 2020 4:40 pm 
Hero Member
Hero Member
User avatar

Joined: Wed Oct 21, 2009 6:10 pm
Posts: 1066
Images: 0
Location: Louisiana
That's what I needed, thank you both. Les, I'm posting your photos from your album here in this thread so I can come back and easily find yours and Bob's photos when its time.

Attachment:
vertical induction off back baffle.jpg
vertical induction off back baffle.jpg [ 339.78 KiB | Viewed 6116 times ]


Attachment:
vertical induction off back baffle 2.jpg
vertical induction off back baffle 2.jpg [ 336.3 KiB | Viewed 6116 times ]


Top
 Profile Personal album  
 
Ryan Allen
 Post subject: Moved to the Airport
PostPosted: Sun Jan 17, 2021 1:26 pm 
Hero Member
Hero Member
User avatar

Joined: Wed Oct 21, 2009 6:10 pm
Posts: 1066
Images: 0
Location: Louisiana
Well, I ran out of room on my garage, so I moved to the airport. I didn't feel like there was much else I could do at home anyway. My next plan is to fit the wings to the fuse. Then install the flaps/ailerons, wingtips, etc. That will give me more time to find an engine.

Attachment:
Resized_20210116_115619.jpeg
Resized_20210116_115619.jpeg [ 655.9 KiB | Viewed 6021 times ]


Top
 Profile Personal album  
 
Ryan Allen
 Post subject: Lycoming 0-361-F1A6
PostPosted: Wed Feb 17, 2021 8:07 am 
Hero Member
Hero Member
User avatar

Joined: Wed Oct 21, 2009 6:10 pm
Posts: 1066
Images: 0
Location: Louisiana
I have come across a Lycoming 0-361-F1A6 out of a Cessna 172RG that looks interesting for my T18. Does anyone know of a reason why this engine would not be a good fit inside a Thorp cowl? Any other issues with running this engine on a T18? I attached a pic of the sump. Thats the only area I could foresee interference with the bottom cowl.

Attachment:
File comment: engine
IMG_E1622-20210212-113533.JPG
IMG_E1622-20210212-113533.JPG [ 104.72 KiB | Viewed 5912 times ]


Top
 Profile Personal album  
 
leewwalton
PostPosted: Wed Feb 17, 2021 7:07 pm 
Administrator
Administrator
User avatar

Joined: Tue Oct 20, 2009 4:09 pm
Posts: 1693
Images: 107
Location: Houston, TX
You should be ok on the sump clearance as this is a horizontally inducted motor (so you can spare some clearance where the carb would be. Which brings up your biggest hurdle .. you'll need to alter the engine mount to accommodate the aft facing carb, which has been done but it is something that comes into play.

_________________
Lee Walton
Houston, TX
N51863,N118LW
KEFD


Top
 Profile Personal album  
 
Ryan Allen
PostPosted: Thu Feb 18, 2021 5:04 pm 
Hero Member
Hero Member
User avatar

Joined: Wed Oct 21, 2009 6:10 pm
Posts: 1066
Images: 0
Location: Louisiana
dang, I don't want to mess with that. Thank you very much for pointing that out.


Top
 Profile Personal album  
 
fytrplt
PostPosted: Thu Feb 18, 2021 6:55 pm 
Hero Member
Hero Member
User avatar

Joined: Tue Oct 20, 2009 8:07 pm
Posts: 1110
Images: 2
Location: Lakeland, Florida, USA
The motor mount mod is not so daunting. You cut the bottom "X" out, then rebuild the "X" with a dip in it and gusset all joints.

_________________
Bob Highley
N711SH
SN 835
KLAL


Top
 Profile Personal album  
 
Ryan Allen
PostPosted: Sat Aug 14, 2021 12:31 pm 
Hero Member
Hero Member
User avatar

Joined: Wed Oct 21, 2009 6:10 pm
Posts: 1066
Images: 0
Location: Louisiana
While I plan to buy an 0-360 for my project, I came across an 0-320 case that I plan to use in order to fit my cowling to the airframe. Can anyone confirm this case will work for fitting my cowl and spinner spacing? Also, does anyone have any old engine mounts they want to get rid of? I would buy them so I can hang this case and fit my cowl. Any input/insight about my plan would be appreciated.

Image


Top
 Profile Personal album  
 
Ryan Allen
PostPosted: Sat Oct 23, 2021 2:27 pm 
Hero Member
Hero Member
User avatar

Joined: Wed Oct 21, 2009 6:10 pm
Posts: 1066
Images: 0
Location: Louisiana
Well, I finally got my junk engine hung today. It took me longer than I expected, but its done.....and man, are those engine mounts expensive or what! Now on to fitting the cowl.

Attachment:
image000000.jpg
image000000.jpg [ 971.21 KiB | Viewed 4748 times ]


Top
 Profile Personal album  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 247 posts ]  Go to page Previous  1 ... 11, 12, 13, 14, 15, 16, 17  Next

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron

[ Time : 0.299s | 14 Queries | GZIP : On ]