Thorp Air Command - T18.net
http://thorp18.com/thorpforum/

Air Filter Assy
http://thorp18.com/thorpforum/viewtopic.php?f=35&t=8251
Page 1 of 1

Author:  Unclerap [ Tue Jul 24, 2018 3:11 pm ]
Post subject:  Air Filter Assy

My T18 has a plastic air filter holder, from my research it is a Matney. It's broken and I want to replace it with a Brackett. It appears the Matney is dimensionally similar to the BA 4210 used on Grummans. Anybody have a suggestion, guidance, etc?

thanks

Rap

Author:  Jeff J [ Wed Jul 25, 2018 8:01 am ]
Post subject:  Re: Air Filter Assy

Mine has a BA-4106 if that helps.


Image

Author:  Binder [ Wed Jul 25, 2018 12:56 pm ]
Post subject:  Re: Air Filter Assy

I'm going to jump in here to ask questions as well. Jeff, what intake assembly do you have?

I have a round car based intake and it's not filtering well. I want to change it to something nice and new like what everyone else is using. I will have a post for it.

Author:  Jeff J [ Wed Jul 25, 2018 5:44 pm ]
Post subject:  Re: Air Filter Assy

I am not 100% sure because I am not where I can check the receipts included in the aircraft file but I think it is this one:
http://www.aircraftspruce.com/catalog/e ... ckkey=3787

I was thinking that I would like to change. There is no seal between my cowl and the air filter.

Author:  Unclerap [ Wed Jul 25, 2018 5:50 pm ]
Post subject:  Re: Air Filter Assy

Jeff, thanks. Brackett 4210 and 4106 appear to be identical dimensions. Don't know the diff. Still researching.

Author:  Binder [ Thu Jul 26, 2018 7:49 pm ]
Post subject:  Re: Air Filter Assy

Jeff J wrote:
I am not 100% sure because I am not where I can check the receipts included in the aircraft file but I think it is this one:
http://www.aircraftspruce.com/catalog/e ... ckkey=3787

I was thinking that I would like to change. There is no seal between my cowl and the air filter.

Thanks for the link, that looks perfect!

That's one thing I was thinking would cause a problem. Pressurized air is getting forced into my lower cowl thus causing less Delta differential for my cylinders. Mine has a gap around the intake and I was wanting to seal it up because I think the ram air is reducing my cooling to the cylinders. This also has a much better carb heat portion. I'll have to find a way to measure my cowl distance and then a way to seal it to the lower cowl to keep air from entering my lower cowl.

My other thought was to run a duct from the back of my baffling like david read did in order to completely remove the scoop and thus reduce drag on this little 290 powered ship!

Author:  Jeff J [ Sun Jul 29, 2018 8:46 am ]
Post subject:  Re: Air Filter Assy

My gap is pretty small so it may not be worth the effort to seal up. I would hate to change it just to have the engine and/or accessories start hitting the cowl again. My setup won’t support it but somewhere in these web pages are pictures of a setup using wetsuit material to connect the cowl to the airbox that I thought would work well.

David’s setup should work good too. I don’t think I have seen pictures of it and I never made it down to meet him.

Author:  Bill Williams [ Sun Jul 29, 2018 12:00 pm ]
Post subject:  Re: Air Filter Assy

Don't remember the name ,but the race car folks use a rubber round tube molded to a thin channel that slips over the edge of aluminum

Author:  Binder [ Mon Jul 30, 2018 5:52 pm ]
Post subject:  Re: Air Filter Assy

Bill Williams wrote:
Don't remember the name ,but the race car folks use a rubber round tube molded to a thin channel that slips over the edge of aluminum


I might have to fiberglass in a round section and just hook scat tubing to it

Author:  Unclerap [ Sat Aug 04, 2018 2:38 pm ]
Post subject:  Re: Air Filter Assy

Closing the loop to my question: The Brackett 4210 is dimensionally identical to the Matney. Fits perfectly.

Rap

Page 1 of 1 All times are UTC - 6 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/