Thorp Air Command - T18.net http://thorp18.com/thorpforum/ |
|
Air Dog DIY remote oil kit http://thorp18.com/thorpforum/viewtopic.php?f=35&t=7976 |
Page 4 of 5 |
Author: | jrevens [ Sun Jan 08, 2017 10:15 pm ] |
Post subject: | Re: Air Dog DIY remote oil kit |
That is just so cool, Bruce! I'm surprised it works so well with aluminum considering all the wood in the structure - usually you have to have a rock-solid metal structure to maintain accuracy and finish of the cut. I'm sure that using the small diameter end mills helps and makes it doable. Was it difficult to learn the programming, or did you already have experience with that? I'm curious - what was the cost of the motors and other parts from China? Again... nice job! |
Author: | bfinney [ Sun Jan 08, 2017 11:47 pm ] |
Post subject: | Re: Air Dog DIY remote oil kit |
John, Dec 2013 the 3-axis electronics, which included 3 425 oz motors, 3 motor drivers, power supply and parallel port break out board was $199, other companies had packages for $390. The fan, power connector and switch were donated from a bad computer power supply. I had the plywood and a router motor. All of the other pieces, hardware, roller chain, sprockets, couplers, wire, etc, etc, etc was about $600. I used cross dowels and 1/4" machine screws to assemble the gantry structure. The finish is not as smooth as it could be most likely do to the flexing of the machine, also I need to check all of the screws to see if any need to be tightened now that I have some run time on the machine. If I had not messed up one of the mount holes it would be a usable part. The finish on softer materials is quite acceptable, i.e. wood and pink foam. For my next try, I'm redoing the program to take a smaller finish cut at a slower speed. |
Author: | Ryan Allen [ Tue Mar 07, 2017 7:04 am ] |
Post subject: | Re: Air Dog DIY remote oil kit |
that looks sharp Bruce. Nice looking work. |
Author: | Rich Brazell [ Tue Mar 07, 2017 4:00 pm ] |
Post subject: | Re: Air Dog DIY remote oil kit |
Bruce my man ! That's some pretty fancy metal whittling ! RB |
Author: | bfinney [ Tue Mar 07, 2017 4:53 pm ] |
Post subject: | Re: Air Dog DIY remote oil kit |
Ah shucks Rich, it twern't nothin |
Author: | bfinney [ Tue Mar 07, 2017 11:52 pm ] |
Post subject: | Re: Air Dog DIY remote oil kit |
Here's a shot of my remote filter mount. |
Author: | fytrplt [ Wed Mar 08, 2017 1:44 am ] |
Post subject: | Re: Air Dog DIY remote oil kit |
Gotta ask. What is the lawn mower gas filter for? |
Author: | bfinney [ Wed Mar 08, 2017 11:37 am ] |
Post subject: | Re: Air Dog DIY remote oil kit |
It smooths out the manifold pressure to my Dynon engine monitor |
Author: | Bill Williams [ Wed Mar 08, 2017 2:10 pm ] |
Post subject: | Re: Air Dog DIY remote oil kit |
Is it really pressure or a vacuum ? Most builders put a fitting that has a small orfice to eliminate the pulsing |
Author: | fytrplt [ Wed Mar 08, 2017 2:17 pm ] |
Post subject: | Re: Air Dog DIY remote oil kit |
Thanks. I just pounded a rivet in the fitting and drilled it out with a #80 drill. |
Author: | bfinney [ Wed Mar 08, 2017 4:08 pm ] |
Post subject: | Re: Air Dog DIY remote oil kit |
Bill, It depends on what your reference is, if you measure as a reduction of atmospheric then call it vacuum, if you measure relative to 0 then it's pressure. On aircraft we measure pressure, on cars vacuum. When the engine is not running the manifold pressure is the same as atmospheric, standard day = 29.92 inHg. If the gauge read zero with the engine off then it would be called vacuum. I also have a screw with a #50 hole in one end of the filter unit. The filter acts as a reservoir and also keeps any gunk that might get in the line from getting to the pressure sensor. |
Author: | jrevens [ Wed Mar 08, 2017 7:31 pm ] |
Post subject: | Re: Air Dog DIY remote oil kit |
There's pressure change, but no real "flow" to that sensor to bring any potential "gunk" into it. A properly sized orifice is all that should be needed to smooth out pulsation. The filter does add a couple more connections and takes up a little precious space back there though. The filter mount looks good Bruce. |
Author: | Ryan Allen [ Wed Mar 08, 2017 7:36 pm ] |
Post subject: | Re: Air Dog DIY remote oil kit |
fytrplt wrote: Thanks. I just pounded a rivet in the fitting and drilled it out with a #80 drill. Dang, that's a good idea. I probably paid $25 for a reduced orifice fitting..... |
Author: | Rich Brazell [ Wed Mar 08, 2017 9:39 pm ] |
Post subject: | Re: Air Dog DIY remote oil kit |
I'll take the filter ! I might be able to use it on my espresso machine ! RB |
Page 4 of 5 | All times are UTC - 6 hours [ DST ] |
Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |