Thorp Air Command - T18.net

Supporting Owners, Builders and Pilots of the Thorp T-18 and its variants.
It is currently Thu Mar 28, 2024 3:24 pm

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 50 posts ]  Go to page 1, 2, 3, 4  Next
Author Message
Rich Brazell
 Post subject: Seats
PostPosted: Thu Nov 25, 2010 1:35 pm 
Hero Member
Hero Member

Joined: Wed Oct 21, 2009 12:33 pm
Posts: 3095
Images: 64
Location: Jamul, CA (San Diego area)
IMHO, if you stick with a plans built (or close to it) frame along with a very high density foam, you will come out lighter and a better fit. By the time you take a "racing seat/boat seat" and send it to the chop shop (to fit), you will have spent more $$$ and invested more time. There is an outfit (can't remember the name right now) that sells seat kits (foam) for the T-18 (they also supply Vans).

RB


Last edited by Anonymous on Thu Nov 25, 2010 1:35 pm, edited 1 time in total.

Top
 Profile Personal album  
 
dickwolff
 Post subject: Seats
PostPosted: Mon May 02, 2011 5:14 pm 
Sr. Member
Sr. Member

Joined: Tue Nov 24, 2009 7:40 pm
Posts: 498
Images: 6
Location: Canada
Well, I finally received my seat kits from CSA. They provide a nice complete kit, pretty much to plan, or close to it, BUT I was surprised to find that the seat tubing was 3/4 x 0.058 wall instead of what the plans called out. (1.0 x 0.095 wall, I think, or in that range.)

Should I be concerned?

_________________
_________
In theory, theory and practice are the same. In practice, they are not.


Last edited by dickwolff on Mon May 02, 2011 5:14 pm, edited 1 time in total.

Top
 Profile Personal album  
 
Rich Brazell
 Post subject: Seats
PostPosted: Mon May 02, 2011 8:07 pm 
Hero Member
Hero Member

Joined: Wed Oct 21, 2009 12:33 pm
Posts: 3095
Images: 64
Location: Jamul, CA (San Diego area)
One year at PTV CSA had a fully upholstered seat sitting on a work bench. I picked it up and it was incredibly light weight ...a big plus ! If the seat has the aluminum sheeting for the back and bottom to tie the entire seat frame together I would not be concerned. I have not heard of ANY complaints about CSA seats.

RB


Last edited by admin on Mon May 02, 2011 8:07 pm, edited 1 time in total.

Top
 Profile Personal album  
 
leewwalton
 Post subject: Seats
PostPosted: Mon May 02, 2011 8:19 pm 
Administrator
Administrator
User avatar

Joined: Tue Oct 20, 2009 4:09 pm
Posts: 1705
Images: 107
Location: Houston, TX
There are a few guys out there flying with seats made from aluminum lawn chairs. (see older NL) I actually had such an airplane for a while. They were pretty stout and very light. My point is that lawn chairs are pretty thin material, most likely not .05. I agree with Rich, i would not sweat it.

_________________
Lee Walton
Houston, TX
N51863,N118LW
KEFD


Last edited by admin on Mon May 02, 2011 8:19 pm, edited 1 time in total.

Top
 Profile Personal album  
 
Jim Mantyla
 Post subject: Seats
PostPosted: Mon May 02, 2011 8:29 pm 
Sr. Member
Sr. Member

Joined: Wed Oct 21, 2009 6:57 pm
Posts: 227
Location: Barrie, Ontario,Canada
Dick,

I think that with the mass of your ass, the seat material will not be an issue.


Jim Mantyla :-)


Last edited by admin on Mon May 02, 2011 8:29 pm, edited 1 time in total.

Top
 Profile  
 
dickwolff
 Post subject: Seats
PostPosted: Tue May 03, 2011 3:39 am 
Sr. Member
Sr. Member

Joined: Tue Nov 24, 2009 7:40 pm
Posts: 498
Images: 6
Location: Canada
Excellent points. Yes, the upside is lightness. Lightness is good. Thanks.

Jim... the mass has gone up a bit... the winter was not kind to my ass.

DW

_________________
_________
In theory, theory and practice are the same. In practice, they are not.


Last edited by dickwolff on Tue May 03, 2011 3:39 am, edited 1 time in total.

Top
 Profile Personal album  
 
jtball
 Post subject: Seats
PostPosted: Tue May 03, 2011 4:28 am 
Newbie
Newbie

Joined: Tue Nov 03, 2009 7:00 pm
Posts: 48
Images: 3
Location: Australia
I used CSA seats. They are great. The only thing I would do different is that the aluminium sheet folds to stiffen the backs should face foreward into the foam. I have trouble adjusting the seat to the rear seat position on the front seat attach points.I have a set in my album on this site.

_________________
James Ball


Last edited by admin on Tue May 03, 2011 4:28 am, edited 1 time in total.

Top
 Profile Personal album  
 
leewwalton
 Post subject: Seats
PostPosted: Tue May 03, 2011 4:52 am 
Administrator
Administrator
User avatar

Joined: Tue Oct 20, 2009 4:09 pm
Posts: 1705
Images: 107
Location: Houston, TX
Jt,
I just looked at your seat picks. You're right, on the back and bottom sheets, the bent up angles are supposed to face into the frame. You need to notch the corners at the angles so that it will clear the tube.
Lee

_________________
Lee Walton
Houston, TX
N51863,N118LW
KEFD


Last edited by admin on Tue May 03, 2011 4:52 am, edited 1 time in total.

Top
 Profile Personal album  
 
Keith S.
 Post subject: Seats
PostPosted: Wed May 04, 2011 4:24 am 
Newbie
Newbie

Joined: Thu Oct 22, 2009 7:00 am
Posts: 19
Location: USA
Anyone have contact information for CSA. I have not heard of they and can not find anything on line. I would like to check them out. I have good frames, but need recovered.

Thanks, Keith

_________________
Keith Schneider
Waynesville Ohio


Last edited by admin on Wed May 04, 2011 4:24 am, edited 1 time in total.

Top
 Profile  
 
leewwalton
 Post subject: Seats
PostPosted: Wed May 04, 2011 4:38 am 
Administrator
Administrator
User avatar

Joined: Tue Oct 20, 2009 4:09 pm
Posts: 1705
Images: 107
Location: Houston, TX
Look on the main forum page, heading "our suppliers".

_________________
Lee Walton
Houston, TX
N51863,N118LW
KEFD


Last edited by admin on Wed May 04, 2011 4:38 am, edited 1 time in total.

Top
 Profile Personal album  
 
Keith S.
 Post subject: Seats
PostPosted: Wed May 04, 2011 2:53 pm 
Newbie
Newbie

Joined: Thu Oct 22, 2009 7:00 am
Posts: 19
Location: USA
OH!, That CSA, Thanks Lee.

_________________
Keith Schneider
Waynesville Ohio


Last edited by admin on Wed May 04, 2011 2:53 pm, edited 1 time in total.

Top
 Profile  
 
dickwolff
 Post subject: Seats
PostPosted: Tue Nov 29, 2011 6:00 am 
Sr. Member
Sr. Member

Joined: Tue Nov 24, 2009 7:40 pm
Posts: 498
Images: 6
Location: Canada
I just discovered that my purchased seat frames are 10 or 15 degrees underbent. Unfortunately they are now assembled.

Did I miss something in a newsletter? The drawing calls for 84 degrees. Is there some technical advantage to 75 degrees?

_________________
_________
In theory, theory and practice are the same. In practice, they are not.


Last edited by Anonymous on Tue Nov 29, 2011 6:00 am, edited 1 time in total.

Top
 Profile Personal album  
 
leewwalton
 Post subject: Seats
PostPosted: Tue Nov 29, 2011 6:19 am 
Administrator
Administrator
User avatar

Joined: Tue Oct 20, 2009 4:09 pm
Posts: 1705
Images: 107
Location: Houston, TX
Dick,
Most seats now are two part and most likely hinged. If yours are a single "L" shape then the advantage to a"righter" angle is allowing the seat to push back farther allowing more leg room.

These are "experimental" aircraft, the greatest variation between airplanes is usually in the cockpit.

_________________
Lee Walton
Houston, TX
N51863,N118LW
KEFD


Last edited by Anonymous on Tue Nov 29, 2011 6:19 am, edited 1 time in total.

Top
 Profile Personal album  
 
dickwolff
 Post subject: Seats
PostPosted: Tue Nov 29, 2011 7:30 am 
Sr. Member
Sr. Member

Joined: Tue Nov 24, 2009 7:40 pm
Posts: 498
Images: 6
Location: Canada
Right! Mine are CSA kit seats with the hinged back.

90 degrees would be a right angle. 84 degrees is what the drawing calls for. ~70 degrees is what my seats are bent to. Consequently, the seat back contacts the rear frame in any seat position.

Unfortunately I didn't check the angle before I put them together. I can't think of any good reason for underbending the frame except maybe to relieve the stress on the light hinges, which are "undersized" because they used 3/4 tubing instead of the 1" called for in the drawing. Did I miss anything?

_________________
_________
In theory, theory and practice are the same. In practice, they are not.


Last edited by Anonymous on Tue Nov 29, 2011 7:30 am, edited 1 time in total.

Top
 Profile Personal album  
 
leewwalton
 Post subject: Seats
PostPosted: Tue Nov 29, 2011 7:55 am 
Administrator
Administrator
User avatar

Joined: Tue Oct 20, 2009 4:09 pm
Posts: 1705
Images: 107
Location: Houston, TX
3/4 is standard (or at least typical) at this point.

The angle. .. My point was that a righter angle would lend itself to a taller pilot and a more obtuse and would lend itself to a shorter fella. As far as the reason, I'm sure you received an approximation from CSA. At this point you could out some "Williams" (as in Bill) and clamp the back to your bench or something solid and tweak another 10 deg out of it.

_________________
Lee Walton
Houston, TX
N51863,N118LW
KEFD


Last edited by Anonymous on Tue Nov 29, 2011 7:55 am, edited 1 time in total.

Top
 Profile Personal album  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 50 posts ]  Go to page 1, 2, 3, 4  Next

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron

[ Time : 0.175s | 13 Queries | GZIP : On ]