Thorp Air Command - T18.net

Supporting Owners, Builders and Pilots of the Thorp T-18 and its variants.
It is currently Fri Dec 15, 2017 10:56 am

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 49 posts ]  Go to page Previous  1, 2, 3, 4
Author Message
SHIPCHIEF
PostPosted: Thu Jul 13, 2017 1:29 am 
Sr. Member
Sr. Member

Joined: Tue Nov 29, 2011 9:05 pm
Posts: 390
Location: USA
Using you're weight and balance from the spreadsheet, and Bruce's fwd and aft limits, I'd say you are in pretty good shape.
I just want to know? did you take the lead off of the engine before you weighed?
Can you make your preferred changes and re-weigh the plane quickly?
Bruce and I are pretty lucky, our EAA chapter has a set of scales, so we can weigh often and for free.
Re-weighing is always better than trying to calculate the moment of the parts that have been added, removed or relocated...

_________________
Scott Emery
EAA Chapter 326
T-18 N18TE


Top
 Profile  
 
Jeff J
PostPosted: Thu Jul 13, 2017 7:19 am 
Sr. Member
Sr. Member

Joined: Wed Aug 31, 2016 8:18 am
Posts: 276
Images: 0
Location: eastern OK
I left everything where I found it except for the wheel pants to do the weigh. Either I am missing a drawing I need or there isn't any CG information to be had on them and I didn't have a copy of the W&B that came with the airplane so I made my own using information I could find searching the forums and news letters. I think I used the % chord numbers that seemed to come up most often with a reference to a T-18.

Just playing with the numbers, it looks like I should be able to remove the lead if I move the battery from the aft part of the baggage area and mount it on the firewall. The scales I have access to aren't very convenient to use (roll around balance beam scales) but I have unrestricted access for the next couple of months if I can find the time to make changes. I was planning on reweighing it if I get the changes done in time but I don't mind doing W&B revisions and weighing again some time down the road.

One of the hose fittings for the remote oil filter is leaking and, since this filter is plumbed to only filter hot oil, I figure it is a good time to remove that entire assembly to free up space for the battery. Even though the oil screen probably wouldn't have to be checked with the filter at every oil change, it should still be checked regularly since it will accumulate bits of carbon and other debris so I don't see where there is enough of an advantage to justify having both.

_________________
"The joke in aviation is, 'If you want to make a million, you'd better start with £10m.' " -Bruce Dickinson


Top
 Profile Personal album  
 
Jeff J
PostPosted: Mon Aug 14, 2017 9:31 am 
Sr. Member
Sr. Member

Joined: Wed Aug 31, 2016 8:18 am
Posts: 276
Images: 0
Location: eastern OK
I removed the filter and screen to install a B&C 700 oil filter adapter with spacer over the weekend. The new unit didn't have the required clearance on my set up. When I cleaned the screen and filter element I discovered the screen was much dirtier than the filter. It's only about 25 hours since major so both would have been done then. Obviously the filter was catching finer particles missed by the screen but the hassle of having both isn't worth it to me so I reinstalled the screen and went flying. I will be exploring other filter options but for now I will run it the way Lycoming built it.

_________________
"The joke in aviation is, 'If you want to make a million, you'd better start with £10m.' " -Bruce Dickinson


Top
 Profile Personal album  
 
Binder
PostPosted: Mon Aug 14, 2017 10:03 am 
Sr. Member
Sr. Member

Joined: Thu Sep 01, 2016 10:50 pm
Posts: 175
Jeff J wrote:
I removed the filter and screen to install a B&C 700 oil filter adapter with spacer over the weekend. The new unit didn't have the required clearance on my set up. When I cleaned the screen and filter element I discovered the screen was much dirtier than the filter. It's only about 25 hours since major so both would have been done then. Obviously the filter was catching finer particles missed by the screen but the hassle of having both isn't worth it to me so I reinstalled the screen and went flying. I will be exploring other filter options but for now I will run it the way Lycoming built it.



I thought about using one as well although my silicon levels in my oil analysis has never been any measurable amount. Since I change every 25 hours anyways Blackstone said it most likely wouldn't change anything worth the expense. I decided against it and will continue to do what I'm doing. If I start getting more silicon into my oil I might switch then but I'll stay with my 25 hour interval since most oil testing shows 30 hours is about the limit of saturation with the 2 major aviation oils.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 49 posts ]  Go to page Previous  1, 2, 3, 4

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to: