Thorp Air Command - T18.net

Supporting Owners, Builders and Pilots of the Thorp T-18 and its variants.
It is currently Thu Mar 28, 2024 10:36 am

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 5 posts ] 
Author Message
Rich Brazell
 Post subject: Funky paint tech tip
PostPosted: Fri Jan 07, 2011 7:35 pm 
Hero Member
Hero Member

Joined: Wed Oct 21, 2009 12:33 pm
Posts: 3095
Images: 64
Location: Jamul, CA (San Diego area)
Are you tired of punching holes in a carb board box...trying to double over masking tape to hold those screws and what nots in place while you spray paint, well check out Uncle Richies Funky paint strip. Nothing fancy, just a left over piece of IKEA kitchen cabinet wall bracket, it has plenty of holes already made

Image Insert:
Image

Put File Caption Here (the stuff used for metal shelving would also work). Put a piece of double sided carpet tape on part of the metal strip and masking tape over the holes. Put your flat/finishing washers (or any other small parts) on the carpet tape. Take your screws and "punch" then thru the masking tape. Paint as required. When done remove the tape and repeat as necessary. I found the carb board works for about one time, then the holes get enlarged and you need to punch more holes. That's my opinion, what's your's ?

RB


Last edited by Anonymous on Fri Jan 07, 2011 7:35 pm, edited 1 time in total.

Top
 Profile Personal album  
 
Victor Thompson
 Post subject: Funky paint tech tip
PostPosted: Fri Jan 07, 2011 9:16 pm 
Jr. Member
Jr. Member
User avatar

Joined: Mon Dec 21, 2009 11:02 pm
Posts: 51
Images: 12
Location: Merrickville, Ontario, Canada
Rich: When I worked on CDN Military aircraft we used wooden paint boards. These boards where about 2 feet long, 12 inches wide and 1/2 inch thick. (2) 3 inch wooden blocks attached to raise the board off the painting table. The board was drilled to hold 50 or so screws and washers. We would put the screw and washer together and paint them together. 1st prime then paint the hardware.

We did not use any separating tape.

This was done for aircraft leaving the repair section on hardware that usually is repetitively removed.

My belief the function of painting is to:
1. Provide warning markings;
2. provide corrosion control; and
3. Finally aesthetics

Your set up works, you may or may not worry about the over spray as your paint strip is narrow. I don't loose to much sleep on paint on attaching hardware as the paint can peel the 1st time the fastener is used.

Just my .02 cents.

_________________
Victor J Thompson
C-GIRQ
"In Memory Of Dad"


Last edited by admin on Fri Jan 07, 2011 9:16 pm, edited 1 time in total.

Top
 Profile Personal album  
 
Rich Brazell
 Post subject: Funky paint tech tip
PostPosted: Fri Jan 07, 2011 9:39 pm 
Hero Member
Hero Member

Joined: Wed Oct 21, 2009 12:33 pm
Posts: 3095
Images: 64
Location: Jamul, CA (San Diego area)
Vic: All you say is spot on, except me drill 50 holes ! Sticking to the tape and pushing thru the tape was more easier. More easier...where are my manners !

RB


Last edited by Rich Brazell on Fri Jan 07, 2011 9:39 pm, edited 1 time in total.

Top
 Profile Personal album  
 
Victor Thompson
 Post subject: Funky paint tech tip
PostPosted: Sat Jan 08, 2011 10:10 am 
Jr. Member
Jr. Member
User avatar

Joined: Mon Dec 21, 2009 11:02 pm
Posts: 51
Images: 12
Location: Merrickville, Ontario, Canada
Rich: I believe a Lockheed CC-130 Hercules use one or two more machine screws than a Thorp T-18.

Small section of Peg board that is already drilled is option 2 and should cut down on your drilling. Cheers.

_________________
Victor J Thompson
C-GIRQ
"In Memory Of Dad"


Last edited by admin on Sat Jan 08, 2011 10:10 am, edited 1 time in total.

Top
 Profile Personal album  
 
fytrplt
 Post subject: Funky paint tech tip
PostPosted: Sat Jan 08, 2011 3:37 pm 
Hero Member
Hero Member
User avatar

Joined: Tue Oct 20, 2009 8:07 pm
Posts: 1140
Images: 2
Location: Lakeland, Florida, USA
I used 3/16" hardware cloth. The mesh lets the spray go through and thus keeps the pressure from the gun from blowing the screws and washers too far. and yes, when you install them, the paint chips off.

_________________
Bob Highley
N711SH
SN 835
KLAL


Last edited by admin on Sat Jan 08, 2011 3:37 pm, edited 1 time in total.

Top
 Profile Personal album  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

[ Time : 0.157s | 13 Queries | GZIP : On ]